This Sloped Laundry Nook Lost Its Wire Shelf and Gained Built-In Storage
Laundry nooks under sloped ceilings can have plenty of wall space without offering many good places for storage. A standard cabinet cannot fit beneath the lowest section, leaving homeowners with wire shelving that holds supplies in view without using the full wall.
Reddit user u/shawnandbrit07 faced that setup with two front-loading machines beneath a sloped ceiling and one wire shelf above them. During the remodel, the shelf came down and the uneven wall gained two forms of storage: a closed cabinet beneath the taller section and a wood shelf extending into the lower slope. Vertical paneling and a black-and-white penny tile floor finished the nook, including “WASH & DRY” spelled across the entrance.
Wire Shelf Put Every Laundry Supply on Display
One white wire shelf provided the nook’s main storage. Bottles and containers lined its top, while the open wall below offered no folding surface or enclosed place for supplies.
Ceiling geometry made a standard row of upper cabinets difficult. Headroom drops from right to left, leaving much less vertical wall space above the washer than above the dryer.
Old Floor Stopped Where the Laundry Nook Began
Gray square tile covered the small rectangle beneath the machines and met the wood floor at the entrance. An exposed transition strip emphasized the boundary between the laundry area and the room outside it.
With both appliances removed, that compact floor area offered enough room for a new surface without changing the surrounding wood flooring.
Wire Storage Came Out Before the Wall Changed
Removing the supplies exposed the shelf’s simple construction: one long wire rack supported by wall brackets. Water damage or staining is also visible across part of the sloped ceiling in this stage of the project.
Once the shelf came down, the full wall became available for a storage layout shaped around the slope rather than running straight across it.
Sloped Ceiling Was Repaired Instead of Hidden
Repair work cleared the damaged ceiling surface and removed the old shelf. Washer and dryer remained protected beneath moving blankets while work continued around them.
Rather than boxing in the entire slope, the remodel kept its original line visible. That decision preserved as much open space as possible above the machines.
Vertical Paneling Added Storage-Room Structure
Narrow vertical boards were installed across the lower portion of all three walls. A horizontal trim board caps the paneling and follows the nook around each corner.
Upper walls stay plain white, separating the lower storage zone from the irregular ceiling above. Plumbing, outlets, and dryer connections remain accessible within the paneled section.
Cabinet Fits Where Ceiling Height Allows It
Instead of forcing cabinetry across the entire back wall, one two-door cabinet sits on the taller right side. Its rectangular shape stops before the ceiling begins its drop.
A wood shelf takes over on the left, running beneath the slope at a height the cabinet could not use. Basket storage and a glass detergent jar occupy that open section without blocking the ceiling line.
Brass Latch Replaced Standard Cabinet Pulls
Recessed-panel doors keep the cabinet face simple, while one brass latch joins the two doors at the center. No pair of knobs or handles interrupts the fronts.
The hardware also adds a small metal detail against the white cabinet and gray-green paneling without requiring more decoration across the compact wall.
Old Tile Came Out Without Expanding the Floor Area
Removing the gray tile exposed the subfloor from wall to wall. Washer hookups, electrical connections, and the dryer vent stayed in their existing positions.
Floor dimensions did not need to change. Instead, the same small rectangle became the place for the remodel’s strongest graphic detail.
Black Penny Tiles Formed Letters Inside the White Field
White penny rounds cover most of the new floor, while individual black tiles create the border and lettering. Building the pattern required placing black rounds among the white sheets rather than installing one uniform mosaic.
Letters were mapped tile by tile before grout locked the design into place. Double black lines also frame the perimeter.
“WASH & DRY” Marks the Entrance
Finished tile turns the floor into part of the laundry-room design. “WASH & DRY” runs across the front edge, positioned where the message remains visible in front of the appliances.
Black border tiles separate the mosaic from the adjacent wood floor, while white penny rounds fill the space beneath the washer and dryer.
Appliances Returned Without Covering the Floor Detail
Washer and dryer sit in their original side-by-side positions, but the lettering remains exposed across the entrance. Their white fronts also connect with the white field of penny tile beneath them.
Gray-green paneling surrounds the machines on three sides, giving the appliances a defined recess instead of leaving them against plain painted walls.
Sloped Space Now Holds Two Types of Storage
Finished nook divides storage according to available ceiling height. Closed cabinetry occupies the tall right side, while the wood shelf reaches left beneath the descending ceiling.
Laundry supplies no longer need to span one exposed wire rack. Items that can stay visible fit on the shelf, while the cabinet provides concealed storage above the dryer.
Same Nook, More Storage Without Changing Its Footprint
Before and after comparison shows how little the basic footprint changed. Washer and dryer remain in the same recess, and the sloped ceiling still determines the shape of the room.
What changed is how each surface works. Wire shelving became a cabinet-and-shelf combination, bare lower walls gained vertical paneling, and gray floor tile became a custom penny-tile field. Even the lowest section beneath the slope now contributes storage instead of ending the shelf run.
Image credits go to Reddit user u/shawnandbrit07 .