He Covered an Unused Bedroom Door With an IKEA LED Panel and Made It Look Like a Real Window
An old bedroom had two doors, but only one was needed. The unused doorway sat behind a wooden secretary desk, leaving a blank, recessed area where a window would have made the workspace more inviting. Removing the door or cutting an opening through the wall wasn’t necessary to change how the space looked.

The homeowner used a square IKEA LED panel, window blinds, and a wooden frame to create the appearance of daylight passing through a window. With the blinds in place, the light comes through the horizontal slats, concealing the panel and making the former doorway resemble a window above the desk.
Reddit user u/SpelledareKarl shared the project in r/ikeahacks, explaining how an IKEA JETSTRÖM LED panel and VECKLARFLY blinds were mounted over the unused door. The frame hangs from over-door hooks, allowing the original door to remain behind the installation.
A Wooden Frame Became the Base for the Fake Window

The homeowner built a rectangular frame from wooden boards, adding crosspieces between the two long sides. The dimensions were chosen to accommodate the mounting points on the 60 × 60 cm IKEA JETSTRÖM panel and the mechanism for the blinds.
The frame provides a mounting surface for both components without fastening them to the old door.
Metal Hooks Allow the Frame to Hang Over the Door

Metal hooks were screwed to the upper ends of the frame so the assembly could hang over the door. This avoided drilling into the existing panel, which the homeowner described as uneven and around 120 years old.

The crosspieces were attached with screws, forming a rigid support for the light panel. The homeowner also added a board near the top to provide clearance for the blind mounting brackets.
The Frame Fits Against the Unused Bedroom Door

The frame was placed against the door, with its upper section extending above the area where the LED panel would sit. The installation occupies the recessed doorway rather than projecting from the surrounding wall.
The original door panels remain visible behind the wooden supports during construction.
An IKEA JETSTRÖM LED Panel Provides the Light

The homeowner mounted the square JETSTRÖM LED panel to the wooden frame. Its rear housing contains the LED strips and electrical components, while the flat front acts as a diffuser.
The panel is designed to provide artificial lighting, but this project uses it to imitate daylight behind window blinds.
The Panel Hangs Above the Secretary Desk

With the assembly mounted, the white panel sits above the desk without removing the old door. The wooden supports remain visible above and below the light, leaving room for the next part of the installation.
A small table lamp, decorative objects, and speakers occupy the top of the secretary desk beneath the panel.
Switching on the Light Changes the Appearance of the Doorway

With the LED switched off, the panel resembles a plain white square mounted in the doorway. Its smooth surface offers little resemblance to a window without the final covering.

When switched on, the panel produces a broad area of white light above the desk. The homeowner connected it to a remote control, allowing adjustments to its brightness and color.
IKEA Blinds Conceal the LED Panel

The homeowner installed IKEA VECKLARFLY blinds in front of the panel, using the additional wooden support to accommodate their mounting mechanism.
The horizontal slats break up the light into bands, creating the impression of sunlight passing through a window. A small red pendant-style decorative lamp hangs in front of the blinds, completing the illusion.
The Unused Door Now Resembles a Window Above the Desk

The completed installation conceals the square LED panel behind the blinds. Light passes between the slats, while the old doorframe surrounds the arrangement, making it resemble a window set into the wall.
The project changes the appearance of the dark corner without cutting through the exterior wall or removing the original door.
The Desk Remains a Workspace Beneath the Fake Window

With the secretary desk open, a computer monitor sits above the fold-down work surface, alongside a keyboard and gaming equipment. The illuminated blinds remain visible behind the monitor, giving the desk area the appearance of a workspace beside a window.
The homeowner explained that the JETSTRÖM panel can be dimmed and adjusted through its remote control. The installation provides artificial illumination rather than real sunlight, but it changes how the unused doorway appears from the room.
Another homeowner used IKEA furniture to change a room’s layout, arranging six BILLY bookcases and a sliding door to create a separate bedroom inside a studio apartment.
Would you cover an unused door with an illuminated fake window, or prefer to leave the doorway exposed?
Images and project details courtesy of Reddit user u/SpelledareKarl, who shared the project in r/ikeahacks.
