DIY Raised Planter Box – A Step-by-Step Building Guide

Learn to make a spring-ready DIY raised planter box with our quick, step-by-step guide. With just some handywork and time, you’ll have a beautiful space to watch your flowers bloom all season long.

raised planter box

What Grows Best in a Raised DIY Planter Box?

A DIY raised planter box can be an amazing addition to your garden.

raised planter box

Besides just flowers for decoration, they can also be used to hold almost anything you can grow in a garden, including spices, fruits, and vegetables.

Some plants do better in planters than others, however, and below are a list of the plants that do the best when grown in a planter.

Foods That Do Best in a Planter:

  • Basil
  • Green Beans
  • Peas
  • Radishes
  • Strawberries
  • Tomatoes
  • Potatoes
  • Peppers
  • Parsley

Flowers That Do Best in a Planter:

  • Begonia
  • Celosia
  • Geraniums
  • Impatiens
  • Coleus
  • Marigolds
  • Petunia
  • Salvia
  • Creeping Phlox
  • Zinnia

What Kind of Wood Should I Use for a DIY Raised Planter Box?

DIY raised planter box

When it comes to creating your DIY raised planter box, you will want to make sure that you build it out of quality wood. 

This is because your planter will likely be spending most of its time outside, and it needs to be somewhat resistant to things like insects and the elements.

Additionally, you need to consider the type of wood you build your planter box out of as well, as this will dictate how sturdy your planter box is, and ultimately, how long it will last. 

For best results you will want to use one of the following types of wood to build your planter box.

  • Cedar
  • Oak
  • Redwood

You can also use pine to create a DIY raised planter box, but pine should only be used for planters that will be placed indoors.

How Deep Should a Raised Planter Box Be?

How Deep Should a Raised Planter Box Be?

Before you start building, you need to have a plan of how deep your raised planter box will be. Different plants will require different depths of soil in order to grow.

Generally, most plants will flourish in 6 to 8 inches of soil. 

There are a few exceptions to this however. Cabbage, for example, requires at least 10 inches of soil to flourish.

The most difficult plants to grow in a planter are carrots, tomatoes, and peppers, because they need a planter of at least 12 inches to flourish. 

Not only that, but they also need to be properly spaced to allow them room to grow. Flowers with large bulbs need a soil depth of at least 14 inches.

So prior to heading to the store to get construction supplies, take the time to make a list of all the plants you would like to grow in your planter, and double check the soil depth you need. 

This will let you know how deep to make your planter box.

Why is Soil Depth Important?

Why is Soil Depth Important?

The whole reason you are building a planter is to grow some beautiful flowers and tasty veggies.

 If the soil in your planter is not deep enough, the plants will be unable to grow proper roots and will not flourish. Improper soil depth will leave you with underperforming plants or seeds that don’t sprout at all.

How Do I Know If My Plants Are Cramped?

Do you think that there might be too many plants in your DIY planter? Or perhaps your plants don’t have sufficient root space in your raised planter box? 

The number one way to know if your plant is experiencing cramped roots is if it starts to have chronically yellowing leaves, and leaves that are too small for the plant.

You may also notice that your plant isn’t growing as prolifically as it did before, and that it is wilting.

What Do You Put in the Bottom of a Raised Wooden Planter Box?

DIY raised planter box

When a raised planter box is on the tall or deep side, you may need to put some items in the bottom to get it at the right height to plant your plants. 

You have many options of what you can fill your planter with. 

Some ideas include:

  • Crushed Aluminum Cans
  • Plastic Milk Jugs
  • Plastic Water Bottles
  • Plastic Soda Bottles
  • Empty Potting Soil Bags
  • Plastic Garden Liner
  • Rocks
  • Pieces of Cement

Step-By-Step To Make DIY Raised Planter Boxes

Whether you want a flower box, an herb garden, or even a place to grow and harvest your very own vegetables, this DIY project allows you to do it – and as a raised box plan, it won’t kill your back to plant (and/or encourages the kids to garden alongside you).

A DIY raised planter box is ideal for anyone who is short of space in their garden or doesn’t have the space to plant anything on the ground. You could even add this to a large balcony in an apartment. If you do have a larger garden, consider making multiple raised planter boxes by repeating our guide here today.

DIY Raised Flower Box-materials

Materials you’ll need to build the Raised Planter Box With Legs:

To build the DIY raised planter boxes, you’ll need to gather the following materials.

  • One (1) 12’ 4×4 redwood post (or four posts cut to 3’ lengths)
  • Two (2) 4’ 1×8 cedar planks
  • Two (2) 2’ 1×8 cedar planks
  • Six (6) 2’ 1×4 cedar planks
  • 2’ wide 1/4″ grid hardware cloth (aka wire mesh)
  • 24 (or more) 1-5/8” exterior screws
  • 16 3/8” x 2” long hex screws and washers
  • Staple gun, ratchet, sander/sandpaper, exterior wood stain
  • Landscape fabric (aka weed barrier)
  • Potting mix or soil + seeds/plants

Equipment Needed:

  • Compound miter saw (aka “chop saw”)
  • Power drill

Part 1: How to build the Raised Planter Box

Step 1: Measure the wood post

DIY Raised Flower Box-kids in mind

Begin by measuring your 4×4 post into four equal lengths.

Step 2: Cutting the wood

DIY Raised Flower Box-miter saw

Use your miter saw to cut the post into four equal 3’ lengths. 

Repeat the process with your other pieces of wood so that you end up with two 4’ lengths of 1×8, two 2’ lengths of 1×8, and six 2’ lengths of 1×4.

remove any type of staple

Remove any type of staple or alien material on the ends of your wood pieces. 

You want your wood to be in the best condition possible at this point in the process, to create the perfect raised planter box for your garden.

Step 3: Angle cutting

miter saw cuts angles

Simply measure and mark 1” lines from what will be the top ends of each of your 4×4 posts. Set your miter saw at a 45” angle, and make four cuts to each post, rotating the post 90 degrees (to a new side) after each cut.

DIY Raised Flower Box-wood finish

This adds a nice finishing touch to the post-tops, which will be visible with this raised planter box plan design.

rotate vertically for angle cutting

If your miter saw doesn’t rotate vertically for angle cutting measure 1” in from the sides of your post, right along the top edge.

Set your miter saw horizontally

Set your miter saw horizontally to cut 45 degrees, then line up the 1” points with the saw and make your cuts. 

Do two opposite sides first, then rotate your post 90 degrees. 

Match your saw blade to the outer cut points, and cut the other two opposite angles.

Complete cutting the tops

Repeat the process described above to complete cutting the tops of all four posts.

Step 4: Measure and Mark the Posts

DIY Raised Flower Box-meassure bottom

Lay your 4×4 posts down and measure 31” from the bottom of each post on just two adjoining sides.

measuring tape for each side

Mark on both sides of the measuring tape for each side.

Marking on both sides

Marking on both sides of the measuring tape gives you two points of reference for levelness. 

What you’re marking is the point at which the top of your 1×8 side boards will be attached.

going to mark two points

On your two 4’ long 1×8 boards, you’re going to mark two points; these are for the hex screws to attach the side boards to the 4×4 posts. 

Measure 1-3/4” in from the sides of your 1×8 boards, and 1-3/4” in from the top/bottom of the boards.

Step 5: Drilling

DIY Raised Flower Box-mark

Make an “X” to mark the precise points you’ll be predrilling for the hex screws.

Line up the top edge

Line up the top edge of the 1×8 board with the 31” mark that you made on one of your posts. Use a drill bit of your choice (example uses a 1/4″ bit) and predrill the holes.

washer then hex screw

Place a washer then hex screw into each predrilled hole.

Tighten up the hex screws

Tighten up the hex screws with a ratchet until they’re pretty tight. Don’t overtighten that the cedar board splits, however. That’s counterproductive. The last thing you want is to ruin your precious work at this point, or you’ll be back to square one. Take your time throughout the process and don’t rush any stage to ensure you create a high-quality DIY raised planter box.

wood measurement for planter box

1-3/4” is a nice measurement here because a 4×4 post really measures in at 3-1/2”, so that makes the hex screws perfectly centered on the post.

Step 6: Attach the Boards

boards are attached to the post

Once both 4’ long 1×8 boards are attached to the posts, it’s time to attach the two 2’ long 1×8 boards. 

The hex screws that attach these two 1x8s shouldn’t hit the other hex screws. 

Note: You can make sure of this by holding up a 2’ board next to the post, and holding up the hex screw as well.

Although you want these next eight hex screws

Although you want these next eight hex screws centered on the posts, you won’t be measuring in 1-3/4” from the sides of your boards because you have to factor in the 3/4″ width of the 4’ board that’s already attached to the post.

DIY Raised Flower Box-mark

So your side markings for your 2’ long 1×8 cedar boards will be 1-3/4” from the top/bottom of your board (same as the 4’ lengths) but 2-1/2” in from the sides. 

(2-1/2” = 1-3/4” [post center] + 3/4″ [other 1×8 actual width])

mark your drilling points

Again, mark your drilling points with an “X.” 

Ensure these are accurately measured on either side for best results.

Step 7: Predrill the Board

Predrill just through the board

Predrill just through the board at this point (as opposed to predrilling through the board and post together). 

Although these holes are further from the ends of the 2’ boards than the holes for the 4’ lengths, it is still highly recommended to predrill. 

Note: Cedar is prone to splitting, and this extra step doesn’t take much time but adds a lot of precision and protection from board split.

Step 8: Attach the Boards to the Posts

boards have been predrilled

When your 2’ boards have been predrilled, have a helper hold up the 4’ board attached to the posts. 

Align one end of a 2’ board with your 31” height line (or with the 4’ board if you prefer; hopefully the alignments are one and the same), and drill a bit into the 4×4 post through the top predrilled hole.

Attach the washer and hex screw

Attach the washer and hex screw into this predrilled hole with a ratchet. 

Repeat for the other top hole, on the opposite side of this 2’ board.

two hex screws holding

At this point, you should have the top two hex screws holding the 2’ board in place while also connecting the posts into a three-sided structure.

Step 9: Repeat the Process on the Other Board

predrill the four holes

Measure, then predrill the four holes on your other 2’ long 1×8 board. 

Pro Tip: You can use the structure as a sort of saw horse, if you’d like. Just take care not to drill into any wood that’s already in use or attached.

Repeat the process

Repeat the process, on this second 2’ board, of attaching just the top two hex screws. 

This stabilizes the structure, making it much easier to install all the bottom hex screws onto a solid structure with the boards accurately in place.

Predrill the posts

Predrill the posts for the bottom holes on your 2’ boards, then install the bottom four hex screws (two per board).

Step 10: Flip Your Planter Box Over

Measure the width of your planter box

Measure the width of your planter box; it should be 2’ wide. 

Carefully flip your planter box over so it’s resting on its post-tops.

Step 11: Prepare the Hardware Cloth

Buy hardware cloth

Take your 1/4″ hardware cloth (aka “wire mesh”) and get it ready to unroll.

Wear gloves when working

Wear gloves. It’s safer, easier, and more efficient. 

Note: While you may be tempted to skip wearing gloves, you’ll want to protect your hands when cutting this material as it can easily scratch or injure you.

additional length from the inside side

Allow for at least 7” of additional length from the inside side of your 4×4 posts, then unroll the hardware cloth until it reaches the other two 4×4 posts. 

Unroll at least 7” more, then mark your cutting spot. Use wire cutters (aka “tin snips”) to cut the hardware cloth.

Step 12: Secure the Hardware Cloth

staples from your staple gun to attach your hardware

Throw a few staples from your staple gun to attach your hardware cloth to what will be the bottom edge of your 4’ long 1×8 sides. 

Only staple near the center of the planter box at this point, just enough to hold the hardware cloth in place while you work out the corners.

Run your extra hardware cloth

Run your extra hardware cloth up one of the 4×4 posts to determine where you should cut to work around the post.

Begin with a short snip

Begin with a short snip in from the side, up to the corner of your post.

Step 13: Finish Off Installing the Hardware Cloth

end of the hardware cloth

Next, snip from the end of the hardware cloth along the corner of your post down until you reach the same horizontal point as your first snip (which should be even with what will be the bottom edge of your 1×8 board).

Repeat for the other post

Repeat for the other post on this end of the planter box so that you can flatten the inner part of the hardware cloth, between the two posts.

DIY Raised Flower Box-flap

Carefully fold the newly cut corner “flap” downward along the post, into the inner portion of your planter box.

Bend the wire cloth

Bend the thin portion of the flap so that it touches the side board.

inside of your planter box

Once the flap is folded and in place on the inside of your planter box, staple the edges of your hardware cloth all the way up to the 4×4 post. 

Repeat for the other flap on this side of your box.

With your hardware cloth stapled

With your hardware cloth stapled into place, you can more easily work with the inner portion, between the two posts. 

Fold it so it will tuck up inside the planter box.

Push the hardware cloth down

Push the hardware cloth down so the fold is even with what will be the bottom edge of your raised planter box.

Step 14: Repeat the Steps on the Other End

flip your box back to upright

This is what your box will look like at this point. Repeat all these steps for the other end of your box, so that you can flip your box back to upright and continue working on it that way.

massive amounts of extra hardware cloth

Because you don’t want massive amounts of extra hardware cloth poking out of your box, to rust, snag, or cause hurt, it’s time to trim. 

We’ll start with the first folded flaps near the box post. 

You only need to keep enough to staple securely, about 2”.

Step 15: Trim the Flaps on All Four Posts

Repeat for the flaps on all four posts

Trim the flap to about 2” high, and throw the rest away. Repeat for the flaps on all four posts.

Staple what’s left of the flaps

Staple what’s left of the flaps securely to the posts or planter side boards.

hardware cloth are short enough

If the ends of your hardware cloth are short enough (anything shorter than 4” is probably fine), go ahead and staple it to the 1×8 end boards.

your hardware cloth are longer

If the ends of your hardware cloth are longer than you want, it might be easier (and less sharp) to simply fold them over and staple them.

Fold the ends of the hardware cloth

Fold the ends of the hardware cloth over so that the ends are sandwiched between the rest of the hardware cloth and the side board. 

Staple in place.

Step 16: Installing the Cedar Boards for Support

hardware cloth is completely secured

When the hardware cloth is completely secured and in place, it’s time to support it with some 1×4 cedar boards. 

Flip your planter box over to rest on its post-tops. Lay out your six 1×4 boards evenly.

Predrill each

Predrill each 1×4 support board as it rests in place on the bottom of the 1x8s. 

The hardware cloth will be sandwiched between these two boards.

Grab some exterior screws

Grab some exterior screws. 

For reference: We had 1-5/8” handy so used those, but anything over 1-1/4” would probably be fine.

DIY Raised Flower Box-predrill

Screw in your screws to the predrilled holes.

Step 17: Sand Down Any Rough Spots

Sand process for wood

Sand any obvious rough spots, such as the ends of your 1×4 boards.

want to sand the post-tops
Lightly sand all other edges

Lightly sand all other edges and corners and surfaces as you want.

DIY Raised Flower Box - wire

Part 2: Finishing the design

Step 1: Treat the Wood

outdoor-friendly wood

Although you’ve (hopefully) used outdoor-friendly wood, like cedar and fir, you’ll still do well to treat the wood to withstand the elements and last longer. 

Let it dry, then move it to the place in your yard, balcony, or deck that you plan on using the raised planter box.

For reference: We used Australian timber oil in Mahogany Flame to stain and protect this planter box. 

Step 2: Add Breathable Landscape Fabric

staple breathable landscape

Cut, fold, and staple breathable landscape fabric (aka “weed barrier”) to the inside of your planter box. 

Note: Make sure you fit this well to avoid any weeds from growing and damaging the plants you plan to add to your raised planter box.

help to keep your soil in the box

Step 3: Add Potting Mix or Soil

Grab a big bag of potting mix

Grab a big bag of potting mix or soil of your choice.

DIY Raised Flower Box-fill

Fill your planter box about 2/3 full. 

Make sure you distribute the soil evenly throughout the raised planter box, so there are no gaps or thinner areas.

DIY Raised Flower Box-colorful rocks

Step 4: The Final Step – Add Flowers, Herbs, or Plants to Your Raised Planter Box

At this point, the raised planter box is yours to do with what you want. 

Throw some vegetable seeds in there, plant a few flowers, section out some herb plots, whatever.

DIY Raised Flower Box-kids planting

 

DIY Raised Flower Box - colorful flower

We love how it brightens up a currently colorless corner of a f our yard. Of course, you could opt for even brighter blooms in your DIY raised planter box, which will soon make it a focal point in your garden.

DIY Raised Flower Box Project

Tuck the box away between a backyard shed and some raspberry bushes. The mahogany flame hue looks fresh and bright in this setting.

 

DIY Raised Flower Box

This is a wonderful addition to a backyard, a front yard, a side yard, or even a deck or balcony. The raised planter box design is easy on one’s back and just different enough from other flower beds or herb or vegetable gardens that it’s eye-catching and a treat to look at. 

Frequently Asked Questions (FAQ)FAQ

How deep should should a raised planter box be?

The best depth to aim for with a raised wooden planter box is eight to twelve inches. Keep this in mind as you build your raised planter box to ensure you can create the perfect depth for plants, flowers, and veggies!

How to plant in raised planter boxes?

First, make sure that the bottom of raised planter box is deep enough to add flowers, and vegetables. Once that’s set, you can add seeds or plants directly into the planter box itself. As the seasons change, your plants will grow beautifully and strong!

How do I keep my planter box from rotting?

To ensure that your planter box has longevity, make sure to install a liner. This will help prevent rot from occurring.

How long do planter boxes last?

These beautiful wooden raised planter boxes with legs can last 10-20 years if maintained!

Raised planter box: Final Thoughts

As you can see, a DIY raised planter box is an amazing addition to your home. 

Not only can it grow almost any plant you can think of, but the fact that you are building it yourself means that it will fit in perfectly into the aesthetic of your backyard.

Building a DIY raised planter box isn’t difficult, so there’s no reason to hesitate. 

Head over to your local hardware store and start building your DIY planter today so you can have the garden of your dreams!